Jan-2022 HP HPE6-A66 Actual Questions and Braindumps
HPE6-A66 Dumps To Pass HP Exam in 24 Hours - DumpExam
NEW QUESTION 16
A network architect is doing a site survey for a new wireless design One concern the company has with the old wireless network is coverage. In some cases, APs would lose power and some employees in the network would lose wireless connectivity. The new design needs to prevent this issue from occurring. During the site survey, what are best practices to be followed in regards to the dBm signal level and the power of the AP to ensure adequate wireless coverage and minimal overlap of AP signals for the new design?
- A. AP power at 100% and a measurement of -65 dBM on the measuring device
- B. AP power at 75% and a measurement of -80 dBM on the measuring device
- C. AP power at 75% and a measurement of -90 dBM on the measuring device
- D. AP power at 50% and a measurement of -65 dBM on the measuring device
Answer: A
NEW QUESTION 17
A network architect needs to plan a new wireless network
- A. Airwave, Central, Windows, Mac OSX, and Linux
- B. Central only
- C. Airwave, Central, and Windows only
- D. Airwave and Central only
Answer: D
NEW QUESTION 18
A network architect is designing a new Wi-Fi solution for a small university The solution will involve two mobility controllers that will be clustered at the campus core Because students use a lot of video in both the dormitory rooms and in the classrooms, the solution will need to support 50Gbps via link aggregation between the controllers and core switches.
Which solution would most cost-effectively meet this requirement for the campus core?
- A. Aruba 7240XM mobility controllers and 3810M switches
- B. Aruba 7220 mobility controllers and 3810M switches
- C. Aruba 7210 mobility controllers and 5406R switches
- D. Aruba 7280 mobility controllers and 5406R switches
Answer: B
NEW QUESTION 19
A company has a warehouse that requires ruggedized APs to provide wireless access The APs need to support these characteristics:
* 2 or more spatial streams
* 802.11 ac and 802.11 n support
Cat 7 Ethernet cabling will be used to connect the APs to POE+ capable switches Link aggregation should be employed between the APs and the Ethernet switches. Which would be the most cost-effective solution that would meet the company's requirements?
- A. AP 375 with external omnidirectional antennas
- B. AP 365 with integrated omnidirectional antennas
- C. AP 510 with external omnidirectional antennas and plastic AP cover
- D. AP 318 with external omnidirectional antennas
Answer: D
NEW QUESTION 20
NewRocket requires a wireless capacity design 30 Aruba 510 APs will be connected to each wiring closet using SmartRate connections. Wireless coverage needs to be provided even if a POE+ switch loses power Because of security concerns, wired video cameras were recently installed throughout the facility. There are 12 of these per floor. 6 per wiring closet. The cameras are 802.11n WiFi capable and have power injectors from which to draw power.
Based on the POE+ needs of the mentioned devices, which solution would meet the POE+ requirements while still providing a redundant and cost-effective Wi-Fi solution for the devices that require POE+ for Building 1, Floor 2?
- A. Two 2930M 24-port POE+ switches
- B. One 2930M 48-port POE+ switch
- C. One 3810M 40G 8 HPE Smart Rate switch
- D. Two 2930F 24-port POE+ switches
Answer: B
NEW QUESTION 21
A network architect is designing a new wired and wireless solution for for a company. The company has two buildings on a campus, which each building has three floors. The campus core will be placed in the basement of Building 1. Each wiring closet has eight strands of multi-mode OM3 grade fiber that connect to a wiring closet of the first floor of the building it is contained, referred to as a main distribution frame (MDF). The maximum distance between a floor's wiring closet and the MDF is 100 feet (30 meters). The maximum distance between the two MDFs and the campus core is no more than 150 feet (45 meters). There are eight strands of multi-mode OM3 grade fiber from these two MDF closets to the campus core.
Based on this information, which type of design should be used and what is the maximum speeds supported all uplinks for the existing the multi-mode fiber?
- A. two-tier and 40 Gbps
- B. three-tier and 40 Gbps
- C. two-tier and 10 Gbps
- D. three-tier and 10 Gbps
Answer: D
NEW QUESTION 22
A customer requires Aruba switches that support Smart Rate ports to connect to Aruba APs Which switching product should the customer purchase that will provide 24 Smart Rate ports per access layer switch'?
- A. Aruba 2930F
- B. Aruba 2540
- C. OfficeConnect 1950
- D. Aruba 2930M
Answer: D
NEW QUESTION 23
NewStellar has a main corporate campus in a business park with two adjacent buildings. Each building has three floors and each floor is 322 x 175 feet (98 x 53 meters) for 56,350 square feet (5,235 square meters) total. The ceiling for each floor is 12 feet (3.6 meters) high with a drop-down ceiling at 10 feet (3 meters). The network architect has given you one floor to analyze, Building 1 Floor 2, shown in the attached exhibit.
This floor has a central main corridor with washrooms, stairs, elevators and supply and network cabinets. There are cubicles around the perimeter of the floor. The central part main corridor's dimensions contain 9,350 square feet (870 square meters). Assuming that wireless coverage is not required in the central area, which square footage (square meter) value should a network architect use when determining the number of APs in a capacity design for each floor?
- A. 47.000 square feet {4,365 square meters)
- B. 56.350 square feet {5,235 square meters)
- C. 55.750 square feet {5,175 square meters)
- D. 338,100 feet {31,410 square meters)
Answer: B
NEW QUESTION 24
Which AP mode allows an AP to operate autonomously?
- A. RAP
- B. AM
- C. OCAP
- D. IAP
Answer: C
NEW QUESTION 25
When determining a customer's agenda and clarifying their expectations for a new HPE/Aruba deployment, which two questions should be asked during the stakeholder checklist? (Select two.)
- A. What is the networking experience of onsite personnel?
- B. What business problems are you trying to solve?
- C. Which help desk system is deployed?
- D. is a request for proposal or actual bill of materials (BOM) required?
- E. What is your anticipated growth of the environment?
Answer: B,D
NEW QUESTION 26
A company is installing Internet of Things (loT) devices to support a smart and energy-efficient environment for a building, including loT devices for heating and air conditioning, lights, and window shades. loT devices of these types are typically classified as which category of devices?
- A. Stationary devices
- B. Nomadic devices
- C. Highly mobile devices (HMD)
- D. Somewhat mobile devices (SMD)
Answer: B
NEW QUESTION 27
A customer requires a campus core virtualization solution that supports a dual control and management planes, as well as active-active forwarding paths. Which solution would meet the customer's requirements?
- A. Backplane stacking
- B. VSF
- C. VSX
- D. Mesh stacking
Answer: A
NEW QUESTION 28
Which component uniquely defines the BSSID when implementing an employee SSID?
- A. Radio MAC address
- B. Wireless device MAC address
- C. Case-insensitive SSID name
- D. Case-sensitive SSID name
Answer: B
NEW QUESTION 29
Which two challenges do802.1ig barcode scanners present to a WLAN design? (Select two.)
- A. encountering RF interference by devices
- B. providing consistent performance on all available channels
- C. implementing adequate security measures to ensure PCI compliance
- D. determining the RF channel bandwidth consumed per Barcode scanner
- E. roaming between APs
Answer: B,C
NEW QUESTION 30
A customer is designing a new wired network. The customer requires 50 Gbps uplinks, VSF logical switching, and smart rate port support Which of the following switches would meet these requirements?
- A. 6300 series
- B. 5400R series
- C. 8300 series
- D. 3810M series
Answer: D
NEW QUESTION 31
A company is redesigning their wireless network and will be upgrading all devices to support the latest wireless standards. The company is not near any radar installations. In order to keep wireless NIC power levels as low as possible to reduce interference issues and to take advantage of radar frequency ranges, what IEEE standard should APs support?
- A. S02.11V
- B. 802.11r
- C. 802.11 ax
- D. S02.11h
Answer: C
NEW QUESTION 32
A high-end theater venue will be implementing an Aruba wireless solution using ceiling- and wall-mounted APs. The venue wants to ensure the the APs blend into the ceiling and wall environments. What solution should the customer use to ensure that wireless coverage is not hampered?
- A. Place the APs above the ceiling and behind the walls
- B. Paint the APs to match the ceilings or walls
- C. Place a strip of tape over the LEDs
- D. Order Aruba AP covers for the APs
Answer: A
NEW QUESTION 33
A network architect is designing a new Wi-Fi solution for a customer The customer currently occupies a one-story building on a small campus. In one part of the building there is an auditorium, where the ceiling height and attenuation is different from the rest of the building. What should the network architect create in VisualRF to identify this difference when planning :ne APs?
- A. Create a Region in the Floorplan View
- B. Spit the Building View into two Floorplan Views
- C. Define the appropriate properties in the Building View
- D. Define the appropriate properties in the Network View
Answer: C
NEW QUESTION 34
A network architect will be using VisualRF to determine the appropriate wireless coverage for a new wireless design. Seamless, uninterrupted roaming is necessary for this design, since voice will need to be supported. Given these requirements, which information should be used in VisualRF to plan a cost effective solution that meets these requirements?
- A. Minimum -80db, 1 AP per 1,000 square feet, very high-density design
- B. Minimum -70db. 1 AP per 5,000 square feet, high density design
- C. Minimum -70db, 1 AP per 2,500 square feet, capacity design
- D. Minimum -65db, 1 AP per 2,500 square feet, high density design
Answer: D
NEW QUESTION 35
A company needs to replace an existing legacy wireless and wired solution with one that supports features like 802 11 ax for APs and logical switching for switches. The company is located on a single floor with two wiring closets. Assume that there will be 10 APs connected via POE+ to each wiring closet, along with 36 wired user connections All switches on a floor should be configured in a single stack. The distance between wiring closets is 100 feet (31 meters).
Which switching solution will minimally provide 10 Gbps uplinks at the most cost-effective price, while still meeting the company's requirements?
- A. 2930F switches
- B. 5406R switches
- C. 2930M switches
- D. 3810M switches
Answer: C
NEW QUESTION 36
A company needs an upgrade of its access layer switches. The solution requires that devices connected to the access layer by authenticated and their traffic processed by the firewall features of the Aruba Mobility Controllers. Which solution should the company implement?
- A. iPsec tunneling
- B. GRE tunneling
- C. PAPI mobility
- D. Dynamic segmentation
Answer: A
NEW QUESTION 37
A network designer is documenting the number of physical sites for a customer that is within the scope of a redesign project. When determining the network purpose at each site, on what should the designer focus at each site? (Select two.)
- A. types of users and their devices
- B. square footage
- C. ceiling height
- D. number of buildings
- E. number of users
Answer: B,C
NEW QUESTION 38
A network architect is designing a wireless solution for a company that is leasing one floor in a multi-floor building in a downtown area. The customer is concerned about ensuring complete Wi-Fi coverage and pin-pointing RF hazards. What type of survey should the network architect perform?
- A. Passive
- B. Virtual
- C. Active
- D. Spectrum clearing
Answer: C
NEW QUESTION 39
A customer placed an order for an ArubaOS 5406R switch and plans to rack mount it in a wiring closet. The dimensions of the switch are 17.5 inches wide (44.45 cm), 6.9 inches high (17.5 cm), and 17.75 inches deep (45.1 cm). How many rack units should a customer plan for this switch?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION 40
......
How much Aruba Certified Design Associate Exam costs
- Examination Name: Aruba Certified Design Associate Exam
- Length of Exam: 90 min
- Passing Score: 67% or higher
- No of Questions: 52 Questions
- Examination Fees: $180 USD
- Types of questions: Performance Based Questions
Exam Topics
The following are covered in HP HPE6-A66 practice exams and HP HPE6-A66 practice test:
- Gather and analyze data, and document customer requirements
- Plan and design an Aruba solution percustomer requirements
- Recommend the solution to the customer
- Produce a detailed design specification document
- Evaluate the requirements, and select the appropriate Aruba solution for the design
Download the Latest HPE6-A66 Dump - 2022 HPE6-A66 Exam Question Bank: https://www.dumpexam.com/HPE6-A66-valid-torrent.html
Buy Latest HPE6-A66 Exam Q&A PDF - One Year Free Update: https://drive.google.com/open?id=1K1K0TgonZ1vWH_TTH-sMwhrd-poamioV
