NACE New 2026 NACE-CIP1-001 Test Tutorial (Updated 100 Questions)
NACE-CIP1-001 Exam Questions Dumps, Selling NACE Products
NEW QUESTION # 27
ISO SA 3 is directly equivalent to:
- A. NACE No. 2/SSPC SP 10
- B. NACE No. 1/SSPC SP 5
- C. NACE No. 3/SSPC SP 6
- D. None of the above
Answer: D
NEW QUESTION # 28
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. commercial blast cleaning.
- B. brush-off blast cleaning.
- C. white metal blast cleaning.
- D. near-white metal blast cleaning.
Answer: B
NEW QUESTION # 29
Digital hygrometers
- A. determine relative humidity, air temperature, and dew point temperature:
- B. are used to measure temperature from a distance.
- C. consist of a bimetallic sensing element protected from wind gusts.
- D. use a thermocouple in contact with the surface to measure temperature
Answer: A
NEW QUESTION # 30
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. holiday.
- B. checking.
- C. cracking.
- D. sagging.
Answer: A
NEW QUESTION # 31
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Near White Metal Blasting
- C. Light Blast Cleaning
- D. Very Thorough Blast Cleaning
Answer: D
NEW QUESTION # 32
Stripe coats are generally applied to:
- A. Edges and corners
- B. Complex geometric shapes
- C. Welds
- D. a), b), and c)
Answer: D
NEW QUESTION # 33
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 6 to 7 mils (150 to 175 microns)
- B. 10 to 12 mils (250 to 300 microns)
- C. 8 to 10 mils (200 to 250 microns)
- D. 5 to 6 mils (125 to 150 microns)
Answer: A
NEW QUESTION # 34
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. inhibitor residues
- B. sulfates
- C. soluble chemical salts
- D. grease and oil
Answer: D
NEW QUESTION # 35
According to SSPC PA 2 a Spot Measurement is:
- A. The average of gauge readings taken in a 4cm (1.5 inch) circle
- B. The overall average of all readings
- C. A single gauge reading
- D. The average of all spot measurements in a given area
Answer: A
NEW QUESTION # 36
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. alligatoring.
- B. checking.
- C. cracking.
- D. blistering.
Answer: B
NEW QUESTION # 37
Osmotic blistering is most likely to occur as a result of
- A. applying tine coating too thin.
- B. airless spray application
- C. overcoating a surface contaminated with chemical salts.
- D. inadequate anchor pattern/surface profile.
Answer: B
NEW QUESTION # 38
The Inspector's Log Book is generally:
- A. Submitted to the client upon project completion
- B. Shared with all parties upon project completion
- C. Shredded by the inspector upon project completion
- D. Retained by the inspector upon project completion
Answer: D
NEW QUESTION # 39
Non Conformance Reports are completed by the Inspector:
- A. When the Inspector deems it to be a significant non-conforming item
- B. In accordance with the specification's definition of a non-conformance
- C. In every instance that an item does not meet the specification requirements
- D. When the Inspector and Contractor deem it to be a significant non-conforming item
Answer: D
NEW QUESTION # 40
ISO SA 2 is defined as:
- A. Near White Metal Blasting
- B. Very Thorough Blast Cleaning
- C. Light Blast Cleaning
- D. Thorough Blast Cleaning
Answer: D
NEW QUESTION # 41
Solvents are added to coating formulations to
- A. dissolve binders and form liquid coatings.
- B. increase film permeability.
- C. provide color.
- D. decrease film permeability.
Answer: A
NEW QUESTION # 42
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the credentials of the Safety Officer on site
- B. Check the PPE used by the Applicators
- C. Assume the role of the Safety Inspector
- D. Act in accordance with the site safety requirements and set an example
Answer: D
NEW QUESTION # 43
Surface profile describes:
- A. The level of surface roughness required after abrasive blasting
- B. The general condition of the surface required after abrasive blasting
- C. The level of surface cleanliness required after abrasive blasting
- D. The initial condition of the surface prior to abrasive blasting
Answer: A
NEW QUESTION # 44
Which of these tests uses a syringe?
- A. Sleeve test
- B. Bresle patch
- C. Potassium ferricyanide
- D. Soluble salts meter
Answer: B
NEW QUESTION # 45
Daily reports are important because:
Select All That Apply
- A. the information impacts future projects.
- B. Management uses them to make personnel decisions.
- C. Inspectors rarely change on a project.
- D. The information aids communication with supervisors.
Answer: A,B,D
NEW QUESTION # 46
Check abrasive blast pressure close to the
- A. substrate
- B. compressor
- C. blast nozzle
- D. blast pot
Answer: C
NEW QUESTION # 47
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 100% of the specified maximum thickness
- B. 90% of the specified maximum thickness
- C. 80% of the specified minimum thickness
- D. 70% of the specified maximum thickness
Answer: C
NEW QUESTION # 48
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 1
- B. Level 2
- C. Level 3
- D. Level 4
Answer: C
NEW QUESTION # 49
Which one of these elements is not necessary for corrosion to occur:
- A. Cathode
- B. Anode
- C. Reference Cell
- D. Electrolyte
Answer: C
NEW QUESTION # 50
Corrosion generally occurs at which of the following sites:
- A. Anode
- B. Cathode
- C. Metallic pathway
- D. Electrolyte
Answer: A
NEW QUESTION # 51
The initial steel condition is important to the NACE Inspector because:
- A. Less abrasive is need if the mill Scale s gone
- B. If the steel is pitted more coating will be required
- C. The Inspector may have to reject the Steel
- D. It affects the final appearance after blasting
Answer: C
NEW QUESTION # 52
......
NACE-CIP1-001 Cert Guide PDF 100% Cover Real Exam Questions: https://www.dumpexam.com/NACE-CIP1-001-valid-torrent.html
Pass NACE-CIP1-001 Review Guide, Reliable NACE-CIP1-001 Test Engine: https://drive.google.com/open?id=1usOhOgWLBI8xbwAkZ4KLpfqCUr2YJQUm
